Difference between revisions of "Kerbodyne ADTP-2-3"
AlpacaMall (talk | contribs) (Matching format with S3 series and C7 Brand Adapter; updating to reflect 1.6 changes) |
AlpacaMall (talk | contribs) (→Trivia: mentioned low cost ratio) |
||
| Line 15: | Line 15: | ||
Like other adapters, the C7 Brand Adapter is used to transition a rocket from a 3.75m radius to a 2.5m radius. | Like other adapters, the C7 Brand Adapter is used to transition a rocket from a 3.75m radius to a 2.5m radius. | ||
| + | |||
| + | == Trivia == | ||
| + | * The ADTP-2-3 has the best cost ratio of any liquid fuel tank; regarding dry cost, it only costs 8.2 cents per unit of propellant stored (or 54.1 cents including fuel). | ||
| + | :* For comparison, most fuel tanks cost ~50 cents per unit of propellant (or ~100 cents wet). | ||
== Variants == | == Variants == | ||
Revision as of 20:44, 24 August 2021
| Kerbodyne ADTP-2-3 | ||
 | ||
| Adapter by Kerbodyne | ||
| Radial size | Large, Extra large | |
| Cost | (total) | 1 623.00 
|
| (dry) | 246.00
| |
| Mass | (total) | 16.875 t |
| (dry) | 1.875 t | |
| Drag | 0.3-0.2 | |
| Max. Temp. | 2000 K | |
| Impact Tolerance | 6 m/s | |
| Research |  Large Volume Containment
| |
| Unlock cost | 12 000
| |
| Since version | 0.23.5 | |
| Part configuration | Size2to3_v2.cfg | |
| Liquid fuel | 1 350 
| |
| Oxidizer | 1 650
| |
The Kerbodyne ADTP-2-3 is a liquid fuel tank containing 15&nbst;t of liquid fuel/oxidizer mixture. Like the C7 Brand Adapter - 2.5m to 1.25m, it is both an adapter and a fuel tank. It is designed to attach size 2 parts to size 3 parts.
It contains slightly less fuel than the Kerbodyne S3-3600 Tank or the Rockomax X200-32 Fuel Tank. Unlike the C7 Brand Adapter, it is the only adapter of its size; no slanted adapter exists.
Product description
| “ | This adapter is used to bridge between Kerbodyne and Rockomax rocket bodies. — Kerbodyne |
” |
Usage
The ADTP-2-3 is a liquid fuel tank containing LF/O mix. This allows it to power liquid fuel rocket engines, like the RE-L10 "Poodle" Liquid Fuel Engine. If there are multiple liquid fuel tanks connected to an engine, then they will all be drained equally to power it. [1] Unlike both the C7 Brand Adapter and the Kerbodyne S3 series tanks, the ADTP-2-3 can only be placed in-line, and cannot be radially mounted.
When full, one tank can power a single RE-L10 "Poodle" Liquid Fuel Engine for up to 205.9 seconds at full thrust, or a single Kerbodyne KR-2L+ "Rhino" Liquid Fuel Engine for up to 25.0 seconds at full thrust.
Like other adapters, the C7 Brand Adapter is used to transition a rocket from a 3.75m radius to a 2.5m radius.
Trivia
- The ADTP-2-3 has the best cost ratio of any liquid fuel tank; regarding dry cost, it only costs 8.2 cents per unit of propellant stored (or 54.1 cents including fuel).
- For comparison, most fuel tanks cost ~50 cents per unit of propellant (or ~100 cents wet).
Variants
As of version 1.6 this adapter has three textures that can be switched in the editor.
Trivia
- Prior to version 1.6, the ADTP-2-3 did not contain any fuel, and was therefore much lighter. While an ADTP-2-3 adapter had a mass of 0.2 tons then, it now has a dry mass of 1.875 tons (presumably added by the fuel tank itself).
- The fuel tank-less version of the ADTP-2-3 can be accessed through the "advanced mode" options in the editor, if a lightweight adapter containing no fuel is needed.
Changes
- New model and texture
- Added 3 variants
- Increased mass from 0.2 to 1.875
- Added Liquid Fuel/Oxidizer
- Initial release
- ↑ This assumes that the flow priority setting has not been adjusted.
