Vehicle Assembly Building/ko
| Vehicle Assembly Building KSC building | ||||||
 | ||||||
단계 3
| ||||||
| 위치 |  커빈 (Kerbin)
| |||||
 Kerbal Space Center
| ||||||
| 고도 | 67 미터 | |||||
| 버전 이후 | 0.7.3 | |||||
- Vehicle Editor redirects here; see also Space Plane Hangar.
우주선 조립 건물(Vehicle Assembly Building; VAB)[1]은 커발 우주 센터에서 우주선 조립이 가능한 두 개의 건물 중 하나로 센터 내에서 단일건물로는 제일 큰 건물입니다. 커발 스페이스 프로그램의 개발 기록을 보면 가장 오래된 건물 중 하나이기도 합니다.
용도
격납고 (SPH)와 마찬가지로 우주선 조립 건물도 기체를 조립하는데 사용됩니다. 사용되는 부품의 목록도 두 곳이 동일합니다. 두 건물의 주요 차이점은 격납고는 비행기 조립의 기준축이 수평이고 조립이 좌우 대칭으로 이루어지는데 반해, 조립 건물은수직 방사대칭이며 기준축이 로켓이 서있는 모양을 따라 수직으로 되어 있다는 점입니다. 하나의 부품을 수직축을 따라 방사대칭으로 1개 또는 2쌍, 3쌍, 4쌍, 6쌍, 8쌍으로 부착할 수 있습니다. 이 곳에서 조립된 로켓은 발사대에서 발사됩니다.
부분 조립체는 로켓 조립시 자주 쓰일만한 부분을 별도로 저장해놓은 후 다른 로켓 조립시 불러와 사용할 수 있습니다. 부분 조립품은 조립동과 격납고 모두에서 불러와 사용할 수 있지만, 연결부품이 호환되도록 설계를 잘 해야 합니다.
화면
방식: 조립 건물 화면 상단에는 몇가지 선택 창들이 존재합니다. The left most controls vary with the current mode the VAB is in. Mode is controlled by the three blue icons just to the left of center along the top. These are: Parts (the default mode), Action Groups, and Crew. These modes are each described on their own page.
Craft Name is in the top center. Clicking on the name allows the user to edit the name before saving the current craft. It also opens a drop down box that lets the user enter longer text such as a description of the vehicle, operations guides, or anything else noteworthy. Clicking anywhere else on the screen closes the drop down box.
Mission Flag is just to the right of top center. It presets the flag used, if this is a manned vehicle, when a Extend-o-matic Series A1 Deployable Flag is placed once landed.
File controls are located along the top right of the screen.
- New - Clears currently active vehicle from the VAB.
- Load - Opens a pop up window to load any previously saved vehicle assemblies.
- Save - Saves the currently active vehicle to disk.
Launch is second in from the top right corner. If not recently saved, overwrites Auto Saved Ship on disk, then switches from the VAB to the Launch pad.
Exit is the rightmost button. It exits the VAB back to the Space Center.
Staging On the right edge of the screen, rising from the bottom, is a dynamic and editable list of the current stages of the vehicle under construction. The game will attempt to build the stages as the user adds parts. However, the user may want to change the order that stages are activated, or edit what happens at each stage.
Notifications are on the bottom, second in from the right. These report completed Contracts.
Contracts are on the bottom, just left of Notifications. These list currently active contracts accepted in Mission Control.
겉모습
The Vehicle Assembly Building is structured around an approximately 100 m tall assembly bay tower (108 m including helipad) located at the center of KSC. A wing extends south from the assembly bay tower, itself taller than most buildings at KSC and structured in three tiers. A smaller, lower wing extends a short distance on the north side. On the roof, there are 2 helipads between the skylights. There are no helicopters in the game[outdated], but the helipads provide a suitable landing target for VTOL vehicles.
On the east face of the assembly bay tower is an 8-leaf vertical lift door[2] approximately 93 m tall. Closed at all other times, during craft assembly the east door is visibly open (giving 50 m clearance) as though ready for the craft to be rolled out. However, craft appear directly on the Launch Pad and the door is never seen in motion. The view outside is always lit as midday regardless of time in-game. Additionally, on the north, west, and south faces of the VAB are large, yellow, swinging doors which appear to be auxiliary entrances.
Kerbal scientists and workers roam the floor while a gauntlet of ground crew remain stationed at the main east door. Utility vehicles drive in and out and onto cargo lifts set in the north and south interior framework of the VAB. Occasionally, the utility vehicles will drive through one another, or through Kerbals on the floor, all without any effect on each other. None of this activity interacts with the build process, though scientists appear to examine the craft and workers hammer, drill, tighten, and wrench thin air.
Just to the northwest of the VAB is the retirement monument to the old Mk1 Pod used in the earliest versions of KSP.
사진
The exterior view of the VAB until 0.21
The interior view of the VAB until 0.21
변경사항
- 자유롭게 추가할 수 있는 부분 조립체를 추가하였습니다.
- 내부 인테리어를 새롭게 하였습니다.
- 보급용 트럭과 리프트의 그래픽을 완전히 새롭게 하고, 커발 엔지니어들을 추가했습니다.
- 내부와 발사대 전경의 모습을 다듬었습니다.
- 땅에 있는 커발이 추가되었습니다.
- 최초 릴리스
주석
- ↑ 이따금 "수직 조립 건물(Vertical Assembly Building)"으로 잘못 불리기도 합니다.
- ↑ Term "multi-leaf vertical lift door" used by real-world maker of similar door for NASA
