Clamp-O-Tron Docking Port Sr./ru

From Kerbal Space Program Wiki
Jump to: navigation, search
Большой стыковочный узел «Хват-О-Трон»
Изображение детали
Стыковочный узел от
Found lying by the side of the road

Размер Большой
Стоимость (полная) 980,00 Funds
Масса (полная) 0,20 т
Аэродинамическое сопротивление 0.25
Макс.температура 2000 К
Объём детали  ?
Ударная прочность 20 м/с
Технология Meta-materials.png Метаматериалы
Стоимость разработки 12 200 Funds
С версии 0.20
Конфигурация модуля dockingPortSr.cfg

Большой Cтыковочный узел "Clamp-O-Tron" (англ. "Clamp-O-Tron Sr. Docking Port") - это стыковочный узел, используемый для стыковки двух космических кораблей.

Использование

Изображенная слева деталь способна к стыковке, в то время, как правая деталь уже пристыкована к топливному баку.

Due to its large radius it provides a much more rigid connection than the small-sized "Стыковочный узел "Clamp-O-Tron" resulting in a lot less wobble. This makes it the preferred choice for docking very large and heavy vessels. Otherwise it is functionally identical to all other docking ports, but a lot heavier than them.

Note that in order to dock two spacecrafts, both must be equipped with docking ports of equal size. When constructing a spacecraft, another part which is not a docking port can be placed on it. That part can then be undocked, but not redocked.

Compared with the other docking ports, it is not obvious which side is the active one. Only the active side can be attached to the active side of another docking port of the same size or detach any part connected to it. The active side has more detail and a ring slightly smaller than the usual diameter. The picture to the left shows which side which should face outside.

Описание изделия

« "Большой Стыковочный узел "Clamp-O-Tron" - это результат интенсивного и дорогостоящего исследования, изучившег проблему укрепления связей при стыковке. Благодаря блестящему предложению сотрудника-швейцара "Почему Вы не сделаете его большего размера?", общественность теперь может наслаждаться действительно волнующими ощущениями от стыковки огромных объектов в космосе.  »

Strength against pulling apart

The strength of docking ports is hard to determine. In real life the strength of a docking port is depended by many factors, basically if you are folding the connection or just pulling it. But who cares about real world here?

  • At a force of 100 kN a little gap between the docking ports is formed. The gap is getting bigger with increasing force.
  • At a force of 1100 kN the docking ports are about a meter apart. Relating to a stress–strain curve this would be the elastic limit.
  • At 1120 kN (a little bit more than a J-2 engine used in the Saturn 5 rocket) the parts are moving slowly apart. This makes the game think the ship is getting longer. This is why the camera - pointing always the center of mass - is moving. At a distance of about 70 meters the docking port are being ripped apart (letting the camera flipping back).

The force on a docking port within a space ship (e.g. when you are pulling something) is much smaller than your engine force because the part being pulled is going with you. To be on the safe side one can use as a rule of thumb that the port stress is the force applied by the mass of the part that is pulled. More accurate would it is the force of the part pulling minus the force of the part that is pulled.

Совместимость

Различные размеры стыковочных узлов "Clamp-O-Tron" ("Стыковочный узел "Clamp-O-Tron", "Малый Стыковочный узел "Clamp-O-Tron" и "Большой Стыковочный узел "Clamp-O-Tron") не позволяет соединяться им друг с другом.

Изменения

0.20
  • Первоначальная публикация.