Convert-O-Tron 250

From Kerbal Space Program Wiki
Revision as of 01:44, 21 June 2021 by Turf (talk | contribs) (Updated radiator requirements for resource conversions, and a bit of rewording)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search
Convert-O-Tron 250
Part image
Converter by
Kerbodyne

Radial size Large, Radial mounted
Cost (total) 8 000.00 Funds
Mass (total) 4.250 t
Drag 0.2
Max. Temp. 2000 K
Impact Tolerance 7 m/s
Research Advanced science tech.png Advanced Science Tech
Unlock cost 24 000 Funds
Since version 1.0
Part configuration ISRU.cfg
Conversion Liquid fuel + Oxidizer
Inputs
Ore 0.5 Units of fuel/s
Electric charge 30 ⚡/s
Outputs
Liquid fuel 0.45 Units of fuel/s
Oxidizer 0.55 Units of fuel/s
Conversion Monopropellant
Inputs
Ore 0.5 Units of fuel/s
Electric charge 30 ⚡/s
Output
Monopropellant Units of fuel/s
Conversion Liquid fuel
Inputs
Ore 0.45 Units of fuel/s
Electric charge 30 ⚡/s
Output
Liquid fuel 0.9 Units of fuel/s
Conversion Oxidizer
Inputs
Ore 0.55 Units of fuel/s
Electric charge 30 ⚡/s
Output
Oxidizer 1.1 Units of fuel/s
Optimum Temp 1000 K
Shutdown Temp 4000 K
Max Cooling 200 kW

The Convert-O-Tron 250 is a converter introduced in version 1.0, and far more efficient than its little cousin, the Convert-O-Tron 125.

Usage

The Convert-O-Tron 250 is a part that consumes ore and electricity to produce various fuels and heat. Any of the four conversions may run at the same time: liquid fuel (LF) and oxidizer (LO) in the stoichiometric 9:11 ratio, LF alone, LO alone, or monopropellant. Each running conversion consumes additional ore and electricity and produces fuel and additional heat. Having an experienced engineer onboard will speed up the process considerably, but does not improve efficiency in any way. Heat will always be produced at a fixed rate of 200kW per running conversion, regardless of engineer staffing, requiring four small radiator per conversion, one large radiator per conversion, or one large TCS per 5 conversions (5 trons running 1 conversion each or 2 trons running 2 and 3 conversions). Note that the unit is limited by max cooling of 200kW which means is it unable to utilize more than 200kW of cooling and as such will overheat somewhat when running 2 or more conversions, lowering the output per conversion.

Operating the Convert-O-Tron 250 on the surface of a planet or moon requires much less careful planning and allows for more flexible vehicle design. A craft used to shuttle fuel to orbit can potentially burn part of its payload to complete rendezvous or transfer unused fuel reserves as part of the payload, and need only bring the fuel necessary for landing down to the surface. By contrast, an ore carrier must carry fuel for both landing and takeoff to the surface, cannot use its payload as emergency reserves, and needs to have its fuel to payload ratios adjusted to operate in different gravity wells or make rendezvous in different orbits efficiently. On the other hand an ore carrier which also has a Convert-O-Tron 250 is very flexible, as it can both refuel itself and optimally refuel other ships whether they use liquid fuel only or oxidizer as well.

Surface installations can use rovers with docking ports to ferry the fuel between the converter and the landed fuel transport craft. Alternatively, either the transport craft or fuel station can move around on wheels to dock and transfer fuel without an intermediate rover. In place of docking ports, the Advanced Grabbing Unit should be used when available because it is significantly easier to connect. Ore carriers only need to bring drills down to the surface, and can take off directly after their tanks are full.

Alternatively, an asteroid or comet with a docked Convert-O-Tron 250 can also be used as a refueling station, and can be more efficient due to its lack of a gravity well and the ability to maneuver the asteroid into a convenient orbit.

Resource Feed and Priority

Convert-O-Tron units are not subject to crossfeed restrictions in any way whatsoever. A Convert-O-Tron unit can refill tanks on the far side of crossfeed disabled parts even when the difficulty option Resource Transfer Obeys Crossfeed Rules is set. Tanks are filled using the same priority as emptying tanks, tanks with higher priority numbers will be filled first.

Efficiency

The conversion of ore to liquid fuel and/or oxidizer conserves mass: raw ore has twice the mass of these products but generates 2 product for each 1 ore consumed. It is possible to power the converter by channeling some of the liquid fuel and oxidizer generated into fuel cells, removing the need for solar panels or expensive PB-NUK Radioisotope Thermoelectric Generators, although doing so effectively lowers the mass conversion ratio from 1:1 to 1:0.925 (or lower, if the fuel cell is also being used to power a 'Drill-O-Matic' Mining Excavator), making it more suitable for surface installations, where the conversion ratio is somewhat irrelevant.

The conversion to monopropellant is significantly less efficient than rocket fuel, with a 1:0.8 ratio. The poor ISP performance of most monopropellant engines compounds this problem. However, refueling station capability may allow smaller monopropellant storage which can slightly improve the thrust to weight efficiency of the other engines.

With no crew the nominal 'load' rate of each recipe is only 5% (.05) of the listed rate. The final effective rate is further multiplied by thermal efficiency and effects energy, ore consumption, and fuel production. When the connected vessel has an engineer onboard, rate improves based on the highest level(Lv) of engineer by 20(Lv0), 40(Lv1), 60(Lv2), 80(Lv3), 100(Lv4), 120(Lv5) percent; for final rates of 25, 45, 65, 85, 105, 125 percent of listed rate. Additional engineers beyond the first provide no benefit, only the highest level applies, for an unlimited number of convert-o-trons with a single engineer.

The maximum conversion rate per Convert-O-Tron 250 with all 3 rocket fuel recipes and level 5 engineer totals the following (Energy, Liquid Fuel, Oxidizer): (112.5, 1.6875, 2.0625)/second, (6750, 101.25, 123.75)/minute, (405k, 6075, 7425)/hour, or (2.43M, 36.45k, 44.55k)/Kerbol day(6hrs).

Product description

This mobile processing plant can take raw materials containing even trace amounts of oxygen and hydrogen, and crack them into useful fuel products. When operated by a skilled engineer, you will be able to operate with better efficiency. These modules operate best at their ideal operating temperatures, and features auto-shutdown in the event of excessive overheating. Radiators can be used to help manage excessive heat.

Kerbodyne

Changes

1.0.5
  • Auto shutdown, new description added, new name
1.0
  • Initial release