Mk1 Command Pod/ko

From Kerbal Space Program Wiki
Jump to: navigation, search


Mk1 Command Pod
파트 이미지
Command pod ~에 의해
Kerlington Model Rockets and Paper Products Inc

직경 최소, 소
비용 (합계) 600.00 Funds
(건조) 588.00 Funds
총 질량ù (합계) 0.84 톤
(건조) 0.80 톤
항력 0.15-0.2
최고저항온도 2200 K
Volume N/A
충돌파괴최소속도 14 미터/초
Research Start.png Start
Unlock cost 0 Funds
버전 이후 0.7.3
설정파일상 이름 mk1Pod.cfg
사령선
피치 회전력 5.0 킬로N·미터
요 회전력 5.0 킬로N·미터
롤 회전력 5.0 킬로N·미터
회전 소비전력
0.048
초·킬로N·미터
탑승정원 (maximum) Crew
(required) Crew
일원추진제 10 Units of fuel
전지용량 50.0 
SAS level × 없음
Inventory Slots 1 slots
Volume Limit 50 리터
Wing
양력 0.35

MK1 사령선사령선으로써 임무를 수행중인 커발을 보호하는데 적합합니다. MK1 사령선은 미국 최초의 유인 우주선인 머큐리 캡슐과 모습이 흡사합니다


내부 시야

MK1 사령선의 내부 시야 모습, 커발은 창문을 통해 밖을 볼 수 있다

MK1 사령선의 선체 내 활동시 시야는 매우 간단하고 실용적으로 설계되었습니다. 중심에는 네비볼이 위치해 있고 오른쪽에는 3개의 스크린이 있습니다 - 상승/하강 속도, 해발 고도 스크린, 레이더 고도 스크린 - 그 실용적인 3개의 스크린들은 마우스를 움직여 볼 수 있습니다. 그리고 네비볼의 왼쪽에는 일렬로 현재 작동 상태를 나타내는 계기판이 있습니다. 패널 뒷편에는 해치와 작은 창문이 있습니다. 그 창문은 게임상의 한계로 푸른빛을 띕니다. 하지만 내부 시야로 보았을 때는 밖이 잘 보입니다

Usage

Usually placed at the top of the rocket, the Command Pod Mk1 provides all functionality of a command module. It has half the torque power of most other manned command modules. This is often sufficient for smaller rockets, though larger ones will require additional control systems.

The Mk1 Command Pod features a tiny radial size node on top, typically used for attaching a Mk16 Parachute, and a small radial size node on the bottom. The pod's crew hatch is outfitted with a small window through which an occupying Kerbal can look out during IVA. On the outside there are two rungs of ladders below the hatch.

The Mk1 Command Pod is also the first command module available in the career mode.

Product description

Originally built as a placeholder for a demonstration mock-up of a rocket, the Mk1 Command Pod was heralded as a far safer and more reliable option than its predecessors by rocket scientists throughout the world. It is now commonly seen in active service.

Trivia

  • The model for this parts was replaced in 버전 0.16, there is a memorial to the original located at the Kerbal Space Center.[1], and another at the Old Airfield.
  • Apparently, the bottom side is a hump, which does not bode well for many parts attached to the bottom. The TR-18A Stack Decoupler works particularly well hiding the hump. There is a good side: the hump looks nice when attaching "tiny" parts to the bottom, and it appears similar to a heat shield.

Gallery

Changes

0.23
  • Added Monopropellant
0.18
  • Added ElectricCharge
0.16
  • Part rebalancing: Mass reduced from 1.0 to 0.8, and crew capacity reduced from 3 to 1.
  • New part model.
0.8.5
  • Exposed Kd, Ki and Kp parameters for tuning the SAS and CommandPod modules
0.8.2
  • (Bug fix) Pod cannot be dropped if an Escape Tower (PunchOut addon) is attached
0.7.3
  • Initial release

References

  1. http://kerbaldevteam.tumblr.com/post/28557698420/obituary-mk1-pod