TT18-A Launch Stability Enhancer/ru

From Kerbal Space Program Wiki
< TT18-A Launch Stability Enhancer
Revision as of 13:46, 26 August 2014 by CrazyCo (talk | contribs) (Created page with "{{:TT18-A Launch Stability Enhancer/Box}} '''Пусковой фиксатор "TT18-A" (англ. "TT18-A Launch Stability Enhancer")''' - это система фиксир...")
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search
Пусковая мачта TT18-A
Изображение детали
Launch clamp от
O.M.B. Demolition Enterprises
Стоимость (полная) 200,00 Funds
Масса (полная) 0,10 т
Аэродинамическое сопротивление 0.2
Макс.температура 2000 К
Объём детали  ?
Ударная прочность 100 м/с
Технология General construction.png Базовая сборка
Стоимость разработки 1 800 Funds
С версии 0.16.0
Конфигурация модуля launchClamp1.cfg
Разрушающее усилие 150
Разрушающий момент вращения 150
Генерируемая ЭЭ 1,0 ⚡/с
Testing Environments
On the surface Нет
In the ocean Нет
On the launchpad Нет
In the atmosphere Нет
Sub orbital Да
In an orbit Нет
On an escape Нет
Docked Нет
Ступень Да
Событие Нет
Трап
Extends Нет

Пусковой фиксатор "TT18-A" (англ. "TT18-A Launch Stability Enhancer") - это система фиксирования для устойчивости, разработанная для удержания летательного аппарата на Стартовом столе перед пуском.

С версия 0.19.1 в перечне последовательности отделения "TT18-A" - это опорный элемент, а не разделитель. Учитывая сокращенное количество деталей, показанных на дисплее отделения ступеней до 0.18, это может быть новшеством.

Использование

The launch clamps prevent unbalanced craft from falling over, and heavy designs from crushing themselves when they first load onto the launchpad.

When using the "TT18-A", keep in mind that it must be decoupled to allow lift off. When the rocket is very powerful, engaging the engines without decoupling can lead to a grand catastrophic failure because it tears the structure apart. A simple solution is to release them in the same stage with the main engines. This way they will release the same moment the engines engage, resulting in a satisfying “clunk” sound as your ascent begins, and a hopefully intact craft. Some smaller rockets, like the Kerbal X, can safely have the engines in a stage before the TT18-A as the thrust is not enough to tear it apart.

It is always a good idea to activate SAS before launch, as the "TT18" decoupler may occasionally push a rocket off vertical and lead to a failed launch.

Jet powered first stages, as they need to spin up, should be decoupled as soon as they are running at full throttle. If other rocket engine/rus on that stage are used as well, the staging should:

  1. Start the jet engines,
  2. Decouple the stability enhancers and start the rocket engines.

If there are "TT18-A" left from the previous launch they will be removed prior to placing a new craft there. While in previous versions[specify] it was needed to be confirmed, this is not required anymore.

Описание изделия

« Пусковой фиксатор "TT18-A" uses ground-breaking fastening technology to significantly increase the stability of spacecraft during the pre-launch phase. While OMB Demolition has been criticized in the past for using "big fancy words for a rocket holder" in their description of their device, none can say the TT18 series doesn't deliver rock-solid clamping action, as advertised. The owner's manual strongly suggests these devices be placed on the bottommost section of the spacecraft, and activated as soon as the engines are lit, for optimal de-clamping performance.  »

Changes

0.18
  • Каждый пусковой фиксатор теперь предоставляет одну единицу электричества в секунду для аппарата, к которому он присоединен.
0.16
  • Первоначальная публикация.