Difference between revisions of "Parts/Aero/ramAirIntake/ramAirIntake.cfg"
From Kerbal Space Program Wiki
< Parts
Nilesrogoff (talk | contribs) (Page created) |
m (*update to 1.0.4;) |
||
(8 intermediate revisions by 4 users not shown) | |||
Line 1: | Line 1: | ||
− | + | {{Part config|Ram Air Intake|2=PART | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
{ | { | ||
− | + | name = ramAirIntake | |
− | + | module = Part | |
− | + | author = C. Jenkins, Porkjet | |
− | + | mesh = RampIntake.mu | |
− | + | rescaleFactor = 1 | |
− | + | node_stack_bottom01 = 0.0, 0.0, 0.0, 0.0, -1.0, 0.0 | |
+ | TechRequired = supersonicFlight | ||
+ | entryCost = 14000 | ||
+ | cost = 2680 | ||
+ | category = Aero | ||
+ | subcategory = 0 | ||
+ | title = Ram Air Intake | ||
+ | manufacturer = C7 Aerospace Division | ||
+ | description = At supersonic speeds, -PATENT PENDING, CLASSIFIED INFO- inside the intake duct deflect the incoming air stream, causing -PATENT PENDING, CLASSIFIED INFO-, which creates a -PATENT PENDING, CLASSIFIED INFO-, thereby greatly increasing the efficency of this unit at high altitudes and speeds. Patents Pending. | ||
+ | attachRules = 1,0,1,1,0 | ||
+ | stackSymmetry = 2 | ||
+ | mass = 0.01 | ||
+ | thermalMassModifier = 12.0 | ||
+ | // heatConductivity = 0.06 // half default | ||
+ | emissiveConstant = 0.7 | ||
+ | dragModelType = default | ||
+ | maximum_drag = 0.3 | ||
+ | minimum_drag = 0.3 | ||
+ | angularDrag = 1 | ||
+ | crashTolerance = 7 | ||
+ | maxTemp = 2400 // = 3400 | ||
+ | fuelCrossFeed = True | ||
+ | bulkheadProfiles = size1 | ||
+ | MODULE | ||
+ | { | ||
+ | name = ModuleResourceIntake | ||
+ | resourceName = IntakeAir | ||
+ | checkForOxygen = true | ||
+ | area = 0.01 | ||
+ | intakeSpeed = 10 | ||
+ | intakeTransformName = Intake | ||
+ | } | ||
+ | RESOURCE | ||
+ | { | ||
+ | name = IntakeAir | ||
+ | amount = 1.0 | ||
+ | maxAmount = 1.0 | ||
+ | } | ||
+ | MODULE | ||
+ | { | ||
+ | name = ModuleAnimateHeat | ||
+ | ThermalAnim = IntakeRampHeat | ||
+ | } | ||
} | } | ||
− | + | }} | |
− | |||
− | |||
− | |||
− | |||
− | } | ||
− |
Latest revision as of 12:13, 27 June 2015
PART { name = ramAirIntake module = Part author = C. Jenkins, Porkjet mesh = RampIntake.mu rescaleFactor = 1 node_stack_bottom01 = 0.0, 0.0, 0.0, 0.0, -1.0, 0.0 TechRequired = supersonicFlight entryCost = 14000 cost = 2680 category = Aero subcategory = 0 title = Ram Air Intake manufacturer = C7 Aerospace Division description = At supersonic speeds, -PATENT PENDING, CLASSIFIED INFO- inside the intake duct deflect the incoming air stream, causing -PATENT PENDING, CLASSIFIED INFO-, which creates a -PATENT PENDING, CLASSIFIED INFO-, thereby greatly increasing the efficency of this unit at high altitudes and speeds. Patents Pending. attachRules = 1,0,1,1,0 stackSymmetry = 2 mass = 0.01 thermalMassModifier = 12.0 // heatConductivity = 0.06 // half default emissiveConstant = 0.7 dragModelType = default maximum_drag = 0.3 minimum_drag = 0.3 angularDrag = 1 crashTolerance = 7 maxTemp = 2400 // = 3400 fuelCrossFeed = True bulkheadProfiles = size1 MODULE { name = ModuleResourceIntake resourceName = IntakeAir checkForOxygen = true area = 0.01 intakeSpeed = 10 intakeTransformName = Intake } RESOURCE { name = IntakeAir amount = 1.0 maxAmount = 1.0 } MODULE { name = ModuleAnimateHeat ThermalAnim = IntakeRampHeat } }