Difference between revisions of "Ablator"

From Kerbal Space Program Wiki
Jump to: navigation, search
m (created italian page)
(Undo revision 80030 by Janos (talk) - edited wrong page, sorry)
Line 1: Line 1:
 
{{:Ablator/Box}}
 
{{:Ablator/Box}}
Il '''Materiale Ablativo''' è una [[resource|risorsa]] fondamentale per il funzionamento della maggior parte degli [[heat shield|scudi termici]]. Durante il [[atmospheric entry|rientro atmosferico]], il materiale ablativo viene lentamente consumato, disperdendo calore. Il materiale ablativo non può essere rifornito o trasferito fra parti diverse. Se uno scudo termico termina la riserva di materiale ablativo, cessa anche di prevenire il surriscaldamento delle parti schermate. Gli scudi ablativi lasciano che il materiale di cui sono composti si bruci ed evapori permettendo la dissipazione di calore. Una eccezione è lo [[Heat Shield (10m)|Scudo Termico Gonfiabile (10m)]], che si affida alla resistenza fluidodinamica per rallentare prima di surriscaldarsi. Dalla versione [[1.2.2]], una barra relativa al surriscaldamento viene mostrata sugli scudi termici. Questa barra non raggiunge mai il punto critico rientrando a velocità "normali", ma può raggiungerlo se il materiale ablativo termina o l'ingresso in atmosfera è troppo veloce o troppo duraturo. Il materiale ablativo si consuma anche quando lo scudo termico si trova a meno di 2500 Mm da Kerbol.
+
'''Ablator''' is a [[resource]] that is a vital component of most [[heat shield]]s. During [[atmospheric entry]], ablator will slowly be consumed, dissipating heat in the process. Ablator can not be replenished or transferred between parts. If a [[heat shield]] runs out of ablator it will stop preventing overheating for shielded parts. Ablation shields work by allowing the material to burn away to dissipate heat. The exception to this is the [[Heat Shield (10m)]], which relies on drag to slow it down before overheating. As of version [[1.2.2]], an overheating bar shows up on ablative heat shields. This bar never reaches the point of explosion reentering at "sane" speeds, but will do so when ablator runs out or the entry is too fast or long. Ablator is consumed when closer than 2,500 Megameters from kerbol.
  
== Parti ==
+
== Parts ==
  
 
{{Stats table heat shields}}
 
{{Stats table heat shields}}
  
== Vedi anche ==
+
== See also ==
 
{{Wikipedia|Atmospheric entry#Ablative}}
 
{{Wikipedia|Atmospheric entry#Ablative}}
  
 
[[Category:Resources]]
 
[[Category:Resources]]

Revision as of 14:29, 12 February 2018

Ablator
Density 1 kg/unit
Transferable No
Tweakable Yes
Drainable No
Flow mode Internal
Cost 0.5 Funds/unit
0.5 Funds/kg
Since version 1.0

Ablator is a resource that is a vital component of most heat shields. During atmospheric entry, ablator will slowly be consumed, dissipating heat in the process. Ablator can not be replenished or transferred between parts. If a heat shield runs out of ablator it will stop preventing overheating for shielded parts. Ablation shields work by allowing the material to burn away to dissipate heat. The exception to this is the Heat Shield (10m), which relies on drag to slow it down before overheating. As of version 1.2.2, an overheating bar shows up on ablative heat shields. This bar never reaches the point of explosion reentering at "sane" speeds, but will do so when ablator runs out or the entry is too fast or long. Ablator is consumed when closer than 2,500 Megameters from kerbol.

Parts

Image Part Radial size Cost
(Funds)
Mass
(t)
Max. Temp.
(K)
Tolerance
(m/s)
Tolerance
(g)
Ablator
HeatShieldSmall.png
Heat Shield (0.625m) Tiny 150
(125)
0.075
(0.025)
3 300 9 50 50
HeatShieldSmall.png
Heat Shield (1.25m) Small 300
(200)
0.3
(0.1)
3 300 9 50 200
HeatShieldLarge.png
Heat Shield (2.5m) Large 600
(200)
1.3
(0.5)
3 300 9 50 800
HeatShieldHuge.png
Heat Shield (3.75m) Extra large 1100
(200)
2.8
(1.0)
3 300 9 50 1 800
Heat Shield (10m).png
Heat Shield (10m) Large / 10m 2 400 1.5 3 500
(3 250)
9 50


See also

Atmospheric entry#Ablative on Wikipedia