Difference between revisions of "Tutorial:Mun Landing"

From Kerbal Space Program Wiki
Jump to: navigation, search
m (Step 2- Launch)
(Step 3- To the Mun)
Line 32: Line 32:
 
==Step 3- To the Mun==
 
==Step 3- To the Mun==
 
[[File:MunarTrajector.png|thumb|300px|A shoddy illustration of how to reach Munar Trajectory in a single orbit.]]
 
[[File:MunarTrajector.png|thumb|300px|A shoddy illustration of how to reach Munar Trajectory in a single orbit.]]
You will want your Apoapsis to intersect the moon's orbit.  If you want to reach the moon on the first swing around, '''wait until you see the Mun rise just above the horizon'''.
+
You will want your Apoapsis to intersect the moon's orbit.  If you want to reach the moon on the first swing around, '''wait until Mun rises just above the horizon'''.  Once it does, begin a forward burn, and keep an eye on your map, as the apoapsis moves out towards Munar orbit.  Hopefully if you've done this right, you will be captured by Munar gravity on the first pass.
  
Hopefully if you've done this right, you will be captured by Munar gravity on the first passOtherwise, you could always wait until you happen to lock.
+
If you are, for some reason, not caught by the moon, just make sure that your apoapsis intersects the Mun's orbit.  When you reach the apoapsis, perform another forward burn to widen your path on the Mun's orbit (but do not circularize!)This will give you a better chance of hitting the Mun, and you can just wait (or timewarp) until you do.
  
 
When you do, turn your craft around and retro thrust to slow down so you do not fly out.  Keep the retro thrust going until you've formed a nice orbit around the Mun.  Because it's gravity is substantially weaker than Kerbin, your velocity will not be very high.
 
When you do, turn your craft around and retro thrust to slow down so you do not fly out.  Keep the retro thrust going until you've formed a nice orbit around the Mun.  Because it's gravity is substantially weaker than Kerbin, your velocity will not be very high.

Revision as of 15:41, 17 September 2012

This tutorial will show you how to land a Kerbal on the moon.

Step 1- Build the Rocket

The kind of rocket that can get you to the Mun and back can be very, very heavy. The ideal sequence for a Mun rocket is 3-4 stages (though more or less are certainly possible).

Let's start from the top down:

A typical Munar lander.

The Upper Stage (Lander) should be deployed in Munar orbit, and should be capable of traveling to the surface of the moon, back to orbit, back to Kerbin orbit, and down into Kerbin's atmosphere. Sounds like a lot, but since most of this occurs in a region with a small gravity well and no atmosphere, it doesn't require much. A couple fuel tanks, a parachute, and at least one light thruster should do it (note that landing legs, RCS, and ASAS are recommended, but not necessary).

Note: It is possible to split this into two stages, 1 for the descent, and 1 for the return home. This is only recommended for heavier, more advanced landers.

A secondary stage seating a lander.

The Middle Stage (Transfer Burn) should be run from just before/during Kerbin orbit, and should end during/after Munar orbit. Depending on how effective your first stage is, this stage should not require much more fuel than the upper stage.

Note: It is also possible to incorporate this stage with the landing stage, though it is not recommended.

The Lower Stage (Launch) Should be big enough to haul everything above it into (or at least close to) orbit above Kerbin. While not required, it is recommended that this stage incorporate some detachable Solid Rocket Boosters (SRBs).

Travel light. The more you incorporate in the top stage, the more thrusters you'll have to add to the stage below, and so on and so forth.

Step 2- Launch

Same as any standard launch, presumably on a much larger scale. See Tutorial: Super-basic Orbiting for dummies.

At around 20,000m begin to tilt your craft east. We are going for a flat, stable, counterclockwise equatorial orbit (same as the Mun). Try to circularize your orbit around 150,000m, though any orbit above the atmosphere (70,000m) is fine. Going any higher than this is not recommended because circularizing a wide orbit just to reach the Mun would waste more fuel.

Ideally, you do not want to ditch your first stage until you have achieved orbit. If your rocket isn't capable of reaching orbit on the first stage, try adding some detachable fuel tanks.

Step 3- To the Mun

A shoddy illustration of how to reach Munar Trajectory in a single orbit.

You will want your Apoapsis to intersect the moon's orbit. If you want to reach the moon on the first swing around, wait until Mun rises just above the horizon. Once it does, begin a forward burn, and keep an eye on your map, as the apoapsis moves out towards Munar orbit. Hopefully if you've done this right, you will be captured by Munar gravity on the first pass.

If you are, for some reason, not caught by the moon, just make sure that your apoapsis intersects the Mun's orbit. When you reach the apoapsis, perform another forward burn to widen your path on the Mun's orbit (but do not circularize!). This will give you a better chance of hitting the Mun, and you can just wait (or timewarp) until you do.

When you do, turn your craft around and retro thrust to slow down so you do not fly out. Keep the retro thrust going until you've formed a nice orbit around the Mun. Because it's gravity is substantially weaker than Kerbin, your velocity will not be very high.

Step 4- The Descent

Select your landing site along your orbital trajectory. Once you are above it, kill your horizontal velocity until the yellow marker sits at the top of the Navball. Eject any stages beneath the lander if you haven't already done so.

Begin a slow, vertical descent. Do not tip your lander over.

See also

With some practice, you may be capable of developing a permanent outpost on the Mun.