Difference between revisions of "Ablator"
AlpacaMall (talk | contribs) m (→Parts: removed 10m ablator-less heat shield) |
|||
| (9 intermediate revisions by 7 users not shown) | |||
| Line 1: | Line 1: | ||
{{:Ablator/Box}} | {{:Ablator/Box}} | ||
| − | '''Ablator''' is a [[resource]] that is a vital component of [[heat shield]]s. During [[ | + | |
| + | '''Ablator''' is a [[resource]] that is a vital component of most [[heat shield]]s. During [[atmospheric entry]], ablator will slowly be consumed, dissipating heat in the process. Ablator can not be replenished or transferred between parts. If a [[heat shield]] runs out of ablator, it will stop preventing overheating for shielded parts. Ablation shields work by allowing the material to burn away to dissipate heat. The exception to this is the [[Heat Shield (10m)]], which relies on drag to slow it down before overheating. As of version [[1.2.2]], an overheating bar shows up on ablative heat shields. This bar never reaches the point of explosion reentering at "sane" speeds, but will do so when ablator runs out, or the entry is too fast or long. Ablator is consumed when closer than 2.500 Megameters from [[Kerbol]]. | ||
== Parts == | == Parts == | ||
| − | + | {{Stats table heat shields|ablator=the fitnessgram™ pacer test is a multistage aerobic capacity test...}} | |
| − | {{Stats table heat shields}} | ||
== See also == | == See also == | ||
{{Wikipedia|Atmospheric entry#Ablative}} | {{Wikipedia|Atmospheric entry#Ablative}} | ||
| − | [[ | + | == Changes == |
| − | [[ | + | ;[[1.9]] |
| + | * Resource is now drainable | ||
| + | ;[[1.2.2]] | ||
| + | * Added display name | ||
| + | ;[[1.2]] | ||
| + | * Added abbreviation (used in [[KerbNet]]) | ||
| + | ;[[1.1]] | ||
| + | * Added volume | ||
| + | ;[[1.0.3]] | ||
| + | * Added hsp value (heat capacity) | ||
| + | ;[[1.0]] | ||
| + | * Initial release | ||
| + | |||
| + | == References == | ||
| + | <references/> | ||
| + | |||
| + | {{Resources}} | ||
Latest revision as of 22:34, 26 September 2021
| Ablator | ||
| Density | 1 kg/unit | |
| Transferable | No | |
| Tweakable | Yes | |
| Drainable | No | |
| Flow mode | Internal | |
| Cost | 0.5  /unit
| |
| 0.5 /kg
| ||
| Since version | 1.0 | |
Ablator is a resource that is a vital component of most heat shields. During atmospheric entry, ablator will slowly be consumed, dissipating heat in the process. Ablator can not be replenished or transferred between parts. If a heat shield runs out of ablator, it will stop preventing overheating for shielded parts. Ablation shields work by allowing the material to burn away to dissipate heat. The exception to this is the Heat Shield (10m), which relies on drag to slow it down before overheating. As of version 1.2.2, an overheating bar shows up on ablative heat shields. This bar never reaches the point of explosion reentering at "sane" speeds, but will do so when ablator runs out, or the entry is too fast or long. Ablator is consumed when closer than 2.500 Megameters from Kerbol.
Contents
Parts
| Image | Part | Radial size | Cost ( ) |
Mass (t) |
Max. Temp. (K) |
Tolerance (m/s) |
Tolerance (g) |
Ablator |
|---|---|---|---|---|---|---|---|---|
 |
Heat Shield (0.625m) | Tiny | 150 (125) |
0.075 (0.025) |
3 300 | 9 | 50 | 50 |
| |
Heat Shield (1.25m) | Small | 300 (200) |
0.3 (0.1) |
3 300 | 9 | 50 | 200 |
 |
Heat Shield (2.5m) | Large | 600 (200) |
1.3 (0.5) |
3 300 | 9 | 50 | 800 |
 |
Heat Shield (3.75m) | Extra large | 1100 (200) |
2.8 (1.0) |
3 300 | 9 | 50 | 1 800 |
See also
Atmospheric entry#Ablative on Wikipedia
Changes
- Resource is now drainable
- Added display name
- Added abbreviation (used in KerbNet)
- Added volume
- Added hsp value (heat capacity)
- Initial release
References
