Difference between revisions of "Tutorial:Orbital Rendezvous/ja"
Kspjptrans (talk | contribs) (Created page with "ドッキングはversion 0.18で実装された。This allows two independently launched components to be intrinsically linked in orbit and allows them to func...") |
Kspjptrans (talk | contribs) |
||
| Line 1: | Line 1: | ||
| − | [[docking/ja|ドッキング]]はversion 0. | + | [[docking/ja|ドッキング]]はversion 0.18で実装されました。これは別々に打ち上げられた機体を軌道上で合体させ、1つの構造物として機能させることができます。ドッキングは惑星間航行用の巨大給油[[space station|ステーション]]など一度の打ち上げでは不可能な規模の構造物を可能にしました。 |
| − | + | ドッキングするには両機の[[Parts#Docking/ja|ドッキングポート]]を接続(ゲーム上は接触)させるのですが、その前に[[w:ja:ランデブー_(宇宙開発)|ランデブー]]しなければなりません。本チュートリアルではその方法を説明します。 | |
== 概要 == | == 概要 == | ||
Revision as of 17:50, 28 October 2014
ドッキングはversion 0.18で実装されました。これは別々に打ち上げられた機体を軌道上で合体させ、1つの構造物として機能させることができます。ドッキングは惑星間航行用の巨大給油ステーションなど一度の打ち上げでは不可能な規模の構造物を可能にしました。
ドッキングするには両機のドッキングポートを接続(ゲーム上は接触)させるのですが、その前にランデブーしなければなりません。本チュートリアルではその方法を説明します。
Contents
概要
- 所要時間: 30～40分
- 難易度: 中
- 対応バージョン: 0.18以降
Preparation
Payload Creation
The first step is to create the payload, this tutorial assumes that you will already have this design started, however keep the following in mind:
- A docking port is required on at least one point of your payload.
- Another port can also be attached so that another section can be daisy chained to it a later stage.
- The sections should be kept at a reasonable size. The only one worth pushing the limits on is the first section, as it will not have to move once in place.
Tug Creation
Next you will need a small orbital tug to push your payload into position. This will mainly be liquid fuel and a small engine controlled by a command module.
A small amount of liquid fuel and an adequate sized engine should be used for the payload. Only a tiny amount is required as it will only have to cover a small distance to the target.
More importantly monopropellant and RCS thrusters are necessary to fine tune the position and allow the docking ports to touch.
After constructing the craft, the center of mass indicator should be used to fine tune the RCS thrusters' positions. The thrusters should be placed symmetrically around the center of mass of the completed craft to allow linear movement without rotation while in space.
Orbital Alignment
There are four distinct stages to an orbital rendezvous:
- Achieving stable orbit
- Fine-tuning orbit sync and inclination to match target
- Matching target orbit
- Dock positioning and locking
Achieving stable orbit
This is covered in other tutorials and I refer you to them. It is however best to get as close to the target's orbit as possible, as it will save heart ache and fuel at a later stage.
Go Build Baby
Tada! Now you've read a full tutorial. Congratulations!
