Difference between revisions of "Tutorial:Orbital Rendezvous"
(Created page with "== Introduction == In version 0.18 docking was introduced. This allows two independently launched components to be intrinsically linked in orbit and allows them to functi...") |
|||
| Line 1: | Line 1: | ||
== Introduction == | == Introduction == | ||
| − | In version 0.18 [[docking]] was introduced. This allows two independently launched components to be intrinsically linked in orbit and allows them to function as a single structure. Functions of such a structure can range from a stationary way point, such as a space station for | + | In version 0.18 [[docking]] was introduced. This allows two independently launched components to be intrinsically linked in orbit and allows them to function as a single structure. Functions of such a structure can range from a stationary way point, such as a space station for refuelling to a large scale interplanetary platform that would be impossible to launch in one piece. |
| − | The way this is accomplished is by linking (essentially touching) two docking ports to each other, after you | + | The way this is accomplished is by linking (essentially touching) two docking ports to each other, after you have moved both components into an Orbital Rendezvous. This tutorial will explain how to achieve this. |
===Specifications=== | ===Specifications=== | ||
| Line 10: | Line 10: | ||
*'''For version:''' 0.18 and Higher | *'''For version:''' 0.18 and Higher | ||
== Preparation == | == Preparation == | ||
| + | === Payload Creation === | ||
| + | Your first order of business is to create your payload, this tutorial assumes that you will already have this design started, however keep the following in mind. | ||
| + | * You will need a docking port on at least one point of your payload | ||
| + | * You may want another port so that another section can be daisy chained to it a later stage. | ||
| + | * You should try and keep your sections to a reasonable size (The only one worth pushing the limits on is the first section as it will not have to move once in place. | ||
| + | === Tug Creation === | ||
| + | Next you will need a small tug to push your payload into position. This will be mainly fuel and small engine controlled by a command part. | ||
| − | + | You should use a small amount of liquid fuel and an adequate sized engine for the payload. You will only need a tiny amount as it will be only to close the final distance. | |
| − | == | + | More importantly you will need mono propellent and RCS trusters to fine tune your position and allow your Docking ports to touch. |
| + | |||
| + | You should build your payload and tug, then turn on your mass indicator to fine tune your RCS position. Ensure that both thrusters are an equal distance from the centre of mass of the complete tug/payload system to allow linear movement without rotation while in space. | ||
| + | == Orbital Alignment == | ||
| + | There are four distinct stages to an orbital Rendezvous | ||
| + | # Achieving stable orbit | ||
| + | |||
| + | # Fine tuning orbit sync and inclination to match target | ||
| + | # Matching target orbit | ||
| + | # Dock positioning and locking | ||
| + | === Achieving stable orbit === | ||
| + | This is covered in other tutorials and I refer you to them. You should however try hard to get as close your targets orbit as possible, as it will save heart ache at a later stage. | ||
| + | === Fine Tuning orbit sync and inclination to match target. | ||
| + | ==Go Build Baby== | ||
Tada! Now you've read a full tutorial. Congratulations! | Tada! Now you've read a full tutorial. Congratulations! | ||
[[Category:Tutorials]] | [[Category:Tutorials]] | ||
Revision as of 12:19, 22 March 2013
Contents
Introduction
In version 0.18 docking was introduced. This allows two independently launched components to be intrinsically linked in orbit and allows them to function as a single structure. Functions of such a structure can range from a stationary way point, such as a space station for refuelling to a large scale interplanetary platform that would be impossible to launch in one piece.
The way this is accomplished is by linking (essentially touching) two docking ports to each other, after you have moved both components into an Orbital Rendezvous. This tutorial will explain how to achieve this.
Specifications
- Length: 30-40 minutes
- Difficulty: Medium
- For version: 0.18 and Higher
Preparation
Payload Creation
Your first order of business is to create your payload, this tutorial assumes that you will already have this design started, however keep the following in mind.
- You will need a docking port on at least one point of your payload
- You may want another port so that another section can be daisy chained to it a later stage.
- You should try and keep your sections to a reasonable size (The only one worth pushing the limits on is the first section as it will not have to move once in place.
Tug Creation
Next you will need a small tug to push your payload into position. This will be mainly fuel and small engine controlled by a command part.
You should use a small amount of liquid fuel and an adequate sized engine for the payload. You will only need a tiny amount as it will be only to close the final distance.
More importantly you will need mono propellent and RCS trusters to fine tune your position and allow your Docking ports to touch.
You should build your payload and tug, then turn on your mass indicator to fine tune your RCS position. Ensure that both thrusters are an equal distance from the centre of mass of the complete tug/payload system to allow linear movement without rotation while in space.
Orbital Alignment
There are four distinct stages to an orbital Rendezvous
- Achieving stable orbit
- Fine tuning orbit sync and inclination to match target
- Matching target orbit
- Dock positioning and locking
Achieving stable orbit
This is covered in other tutorials and I refer you to them. You should however try hard to get as close your targets orbit as possible, as it will save heart ache at a later stage. === Fine Tuning orbit sync and inclination to match target.
Go Build Baby
Tada! Now you've read a full tutorial. Congratulations!
