Difference between revisions of "Decoupler and separator"

Revision as of 01:37, 10 August 2023

Decouplers and separators are parts that allow detachment of one vehicle section from another. Sometimes "decoupler" is used as a generic term for both types of staging devices, decouplers and separators, because both behave in a similar manner.

Mode of operation

Decouplers remain attached to one section of the vehicle when staged. This asymmetric detachment is the distinguishing feature of decouplers when compared to stack separators, which detach from both sections symmetrically. On many models, the attachment affinity of the decoupler can be determined by an arrow decal which points towards the explosive end of the decoupler. The momentum it imparts is defined by the name ejection force which is given in multiples of 10 Ns.

By default, neither decouplers nor separators provide automatic crossfeed, and thus isolate fuel consumption within the respective stages. But both crossfeed and and staging properties can be tweaked - and these can be usefull at emergency decoupling options or when additional fuel is necessary, for example upon unplanned disassembly.

• Force Percent - bar for tweaking the ejection force
• Decoupler: Disable/Enable Staging
• Enable/Disable Crossfeed

Sequencing

All actions in the same stage as the decoupler or separator are executed simultaneously, including those on the detached section, even if that section is isolated from all command modules by the decoupling event itself.

Types

Decouplers exist in both inline and radial designs.

The symmetry selector in the VAB

Radial decouplers, such as the TT-38K Radial Decoupler, attach to the sides of a rocket and eject stages horizontally. Among the uses for these are boosters and asparagus staging. As the ejection force may not be enough to prevent collision afterwards, the Sepratron I can be used to push detached stages away. Radial decouplers and booster or asparagus stages are generally used with symmetry applied in the VAB to ensure the center of mass and center of thrust remain on the rocket's main axis.

Separators, such as the TS-12 Stack Separator, are a special type of vertical decouplers, which separate from both sides, leaving three craft: both sides of the separator and the separator itself. Separators' mass and cost are slightly more than the similarly sized decouplers.

The TT18-A Launch Stability Enhancer, though it is categorized as a strut and is fixed to the ground, also separates can also be classified as a decoupler, although one side is fixed to the ground. But the sound effects are similar and they share the same functionality, separating two parts.

Application notes

Post firing concerns

Care should be taken to ensure that jettisoned engines on radial stages have finished burning before detachment, as there is the risk that they will collide with the rest of the rocket. The main reason for that is, that the decouplers are usually placed below the center of mass of decoupled stages, which means that on separation they induce torque pointing the stage inward. If the engines are shut down, this is usually not a large problem because the rocket can clear it fast enough, but if they are running they will push the stage inward.

Also, the decoupler normally stays on the spent stage the center of mass is closer to the rocket than the center of thrust. This will also induce torque pointing inwards, but this torque is only induced by running engines. If they are stopped they won't induce torque this way. Almost empty booster stages are also relatively light causing a higher acceleration and overtaking the rocket. Both effects cause jettisoned stages which are still running to crash into the rocket in most cases.

Leaving stacked decouplers attached to an engine renders that engine ineffectual. Although the engine will ignite, it will provide no thrust because it's blocked by a part. Jettisoning a stacked decoupler shortly to soon is not a large problem as long as the rocket doesn't rotate.

Synthesized separators

Synthesized Stack Separator using 2 TR-18A Stack Decouplers. (Note the opposing orientation)

It is possible to create a separator out of 2 properly oriented decouplers (at the small expense of additional weight and cost over a bonafide separator). It may be helpful to include both decouplers in the same launch stage.

Explosive decoupling

At the start of Career Mode, no decouplers or separators are available, so normal staging is not possible until enough science has been earned to research these parts. However, there is an art of staging by placing solid fuel boosters next to each other, either connected at the side or arranged vertically so the exhaust of the upper booster fires onto the lower (they don't have to be directly joined). The idea is to build up heat through contact and rocket exhaust to cause overheating resulting in an explosion, decoupling the segments below it approximately when desired, like normal staging.

KSP YouTuber Scott Manley exploited explosive decoupling for a technique he calls "rocket surgery," describing it as more an art form than a science. Using this he was able to go all the way to Minmus and return with only Start technology in his video "Kerbal Space Program - 0.22! Lets Do Science! Lots Of Science".

Although explosive decoupling is possible with other engines, decouplers are more flexible and reliable for staging, and the first decoupler can be researched after a simple first launch collects a small amount of science. So explosive decoupling is less useful except as a gimmick to show what is possible from the start.

As a means of propulsion

Because decouplers and separators exert force on the separated parts, it is possible, though rarely productive, to use them as a means of propulsion. These are called “separator cannons” or “staging cannons.” The more the explosive force and the less payload mass in this “decoupler rocket”, the more altitude or speed will be gained from the separation. The extra-large radial size decoupler and separator have the highest ejection impulse.^[1]

Decouplers

Image	Part	Radial size	Cost ()	Mass (t)	Max. Temp. (K)	Tolerance (m/s)	Tolerance (g)	Ejection impulse (kgF∙s)[Note 1]
	TT-38K Radial Decoupler	Radial mounted	600	0.025	2 000	8	50	250
	TT-70 Radial Decoupler	Radial mounted	700	0.05	2 000	8	50	260
	Hydraulic Detachment Manifold	Radial mounted	770	0.4	2 000	8	50	450
	TD-06 Decoupler	Tiny	150	0.01	2 000	6	150	50
	TD-12 Decoupler	Small	200	0.04	2 000	6	150	100
	TD-25 Decoupler	Large	300	0.16	2 000	6	150	150
	TD-37 Decoupler	Extra large	375	0.36	2 000	6	150	200
	TS-06 Stack Separator	Tiny	215	0.01	2 000	6	150	50
	TS-12 Stack Separator	Small	275	0.05	2 000	6	150	100
	TS-25 Stack Separator	Large	400	0.21	2 000	6	150	150
	TS-37 Stack Separator	Extra large	500	0.48	2 000	6	150	200

References

1. ↑ “Kerbal Space Program - Decoupler Launching Guide” on YouTube by Stun_gravy