Tutorial:How to get to Jool

Jool. If you don't see this at some point during the tutorial, you've probably done it incorrectly.

Traveling to Jool

Jool is the second most distant body in the Kerbol system, and one of the more time-consuming locations to reach. Getting to Jool is really the next step after Eve and Duna, and is an attractive target due to its large atmosphere and complex moon system.

Specifications

• Length: 1–3 hours
• Difficulty: Moderate/Hard
• For version: .17

Additionally, you will need a good understanding of orbital mechanics (see Tutorials section), angles, and a lot of patience.

Steps

Step 1 - Build Your Rocket

This rocket should be fully capable to reach Jool. To build this rocket, you will need at least 8,300 Delta-V. To save some Delta-V in your rocket, you could aerobrake around Jool or Lathe. Ideally, in Career mode, you should have a fully upgraded level 6 Technology tree to build this rocket. You could probably get away with a level 5 Technology tree but you will probably need to add more stages or more power to the bottom stage to make this design work.

Upper Stage

This stage should have enough fuel to get into Jool orbit and to travel around Jool's 5 moons. You can reduce the required fuel by aerobraking inside Jool's atmosphere. At a bare minimum, use a Rocketmax Jumbo-64 Fuel Tank and ether a RE-L10 "Poodle" Liquid Fuel Engine or a LV-N "Nerv" Atomic Rocket Motor on the end.

Middle Stage

The middle stage should be able to escape Kerbin's SOI and get an encounter with Jool. A Rocketmax Jumbo-64 Fuel Tank will do for most small rockets but it depends on the size of your upper stage.

Lower Stage

This is the launcher stage that will get the rocket into orbit. Make sure you use a lot of Solid rocket booster and powerful engines. The size of your lower stage greatly depends on the size and mass of the middle and upper stages.

Step 2 - Planetary Alignment

While not absolutely essential, the easiest and fastest way to reach Jool from Kerbin is ensuring that they are properly aligned. Otherwise, you may spend a lot of time (possibly years) and fuel drifting until they happen to match up. To do so, check your map and make sure that Jool is in front of Kerbin in its orbit around Kerbol, and if you were to draw a line from Jool to Kerbol to Kerbin, it would form a ~90 degree angle.

Alternatively, you can visit The Interplanetary Guide and Calculator to calculate your own path.

Step 3 - Launch to Kerbin Orbit

You should first launch your main ship into orbit and then dock different landing modules to it in orbit

Step 4 - Fly from Kerbin to Jool

Make a maneuver node that is prograde and when you get a jool encounter burn to complete the maneuver

Step 5 - Arriving at Jool

When you arrive at jool you have 3 options: 1) aerobrake If possible I recommend using laythe and not jool due to jools thick atmosphere which is more prone to overheating your ship than laythe. Put your periapsis at 15km and also I suggest using several Klaw-heat shield modules which have probe cores and RCS to dock to your engines temporarily to protect them from exploding. 2)tylo Gravity assist Read the gravity assist page for detailed instructions on a RETROGRADE a gravity assist. 3) burn fuel The crude and fuel wasting method but is easier to perform. Just burn retrograde when you are at your jool periapsis.

After circulation

You should put your orbit in a moon unaffected region

Step 6 - Traveling to its moons

One by one you should deploy landers to go to each of the moons and do lots of science.

on the moons

When you have landed on each moon make sure you take and store all the data in your command pod as this will make your life easier in space. Then take off into jool orbit

docking back together

Dock ALL the landing devices back together to the main ship. transfer all fuel, electricity, xenon, ore and Monopropellant to the main ship and have your kerbals go on EVA and take the data and jet pack to your main ship crew quarters(I do know that crew transfer exists but this is for science purpose)and make sure no science or resources are stored on board the landing devices and then undock all of them or risk not getting to kerbin by taking them with you.

the return

Make sure kerbin is behind jool and now escape jool and then burn what you need to burn to make your periapsis one the orbit of kerbin and you should get an encounter. Put your periapsis at 30-20km and swiftly get rid of any engines or fuel tanks and start the re-entry procedure.

Final Word

You have successfully done a mission to the joolean system and now you have explored most of the kerbol system and now you can build bases, send rovers and more to the planets of kerbal space program. Have fun!

Ideas

Re do the Galileo probe entry to Jupiter

Try a low mass Jool ship using Ion engines.