Difference between revisions of "Radial size"

Revision as of 05:38, 15 May 2015

Comparison of radial sizes with a Kerbal for scale. From top to bottom: Tiny (Size 0), Small, Large, and Extra Large (Size 3).

The radial size is the diameter or mounting position for most parts. If the mounting position is not radial, then the part is either round or one of two special forms. Such rectangular parts as the M-1x1 Structural Panel lack a radial size or it's a size to the next bigger diameter like the Probodobodyne QBE. Four radial sizes exist with varying names. The size scale looks like the internal definition as the Mk2 to size 1 Adapter uses this term and starts with 0 and many values in computer programming are starting from 0 rather than 1.

Any stackable part can be connected to any other stackable part. Matching radial sizes only serves to give a rocket a cleaner visual appearance, and several adapter parts exist to allow transitions between radial sizes while maintaining an unbroken surface.

Sizes

Rocket

The typical mass ratio for rocket fuel is 9.

• Tiny / 0.625m. Typically used for probes and nose electronics.
• Small / 1.25m. The most common size, and the primary size available at the beginning of the game.
• Large / 2.5m / Rockomax.
• Extra Large / 3.75m / Kerbodyne.

Spaceplane

Spaceplane parts may carry either rocket fuel or liquid fuel. Compared to rocket parts they tend to have a poorer mass ratio (usually about 8), but better crash tolerance and maximum temperature.

• Mk1. Like the 1.25m rocket size, this size is a cylinder. All inline air intakes are of this size, but there are no rocket fuel tanks.
• Mk2. With its side chines, this spaceplane size is reminiscent of the real-world Lockheed SR-71 Blackbird. It is between the 1.25m and 2.5m sizes in cross-sectional area. These parts feature a small amount of lift.
• Mk3. Reminiscent of the real-world Space Shuttle. The cross-sectional area is similar to the 3.75m rocket size.

Adapters

1:1 parts between the same size are not shown.

		Fore size
		Nose	Tiny	Small, Mk1	Mk 2	Large	Mk 3	Extra Large
Aft size	Tail			Tail Connector A Tail Connector B
	Tiny	Small Nose Cone ⚡ CH-J3 Fly-By-Wire Avionics Hub
	Small, Mk1	Advanced Nose Cone - Type A Advanced Nose Cone - Type B AE-FF1 Airstream Protective Shell (1.25m) Aerodynamic Nose Cone Mk1 Cockpit	FL-A10 Adapter FL-A5 Adapter NCS Adapter Mk1 Command Pod	TVR-200 Stack Bi-Coupler (2) TVR-1180C Mk1 Stack Tri-Coupler (3) TVR-2160C Mk2 Stack Quad-Coupler (4)	Mk2 Bicoupler (2)	Rockomax Brand Adapter 02 TVR-200L Stack Bi-Adapter (2) TVR-300L Stack Tri-Adapter (3) TVR-400L Stack Quad-Adapter (4)
	Mk2	Mk2 Cockpit		Mk2 to 1.25m Adapter Mk2 to 1.25m Adapter Long
	Large	AE-FF2 Airstream Protective Shell (2.5m) Protective Rocket Nose Cone Mk7		C7 Brand Adapter - 2.5m to 1.25m C7 Brand Adapter Slanted - 2.5m to 1.25m Rockomax Brand Adapter Mk1-2 Command Pod PPD-12 Cupola Module	2.5m to Mk2 Adapter
	Mk3			Mk3 Cockpit	Mk3 to Mk2 Adapter	Mk3 to 2.5m Adapter Mk3 to 2.5m Adapter Slanted
	Extra Large	AE-FF3 Airstream Protective Shell (3.75m)				Kerbodyne ADTP-2-3	Mk3 to 3.75m Adapter

Assets

When creating assets, the correct diameter for a desired model can be found in the table below. The "meter scale" refers to the actual model's diameter, which is then typically scaled up via the default rescaleFactor of 1.25, to give the "actual" in-game diameter. Size scale is used to denote the standard when selecting a node size.

As a special radial size Radial mounted appears. Parts like Rockomax 24-77 so lack general metric counterparts as to eliminate confusion.

Non-cylindrical sizes named “Mk2”, and “Mk3” exist and are used by fuselage parts intended for spaceplanes.

Additional sizes

Several addons add additional, usually larger, radial sizes which are roughly following the stock size scale. There are up to 9 meter parts in the B9 Aerospace mod and mods like Tweakscale can scale parts more freely.