Difference between revisions of "PPD-12 Cupola Module"
From Kerbal Space Program Wiki
THEMUNROVER (talk | contribs) m (→Usage: Reworded to match the reduced mass in 0.25) |
m (-version template usage and link directly;) |
||
Line 25: | Line 25: | ||
== Changes == | == Changes == | ||
− | ; | + | ;[[0.25]] |
* Mass reduced to 1.76 (dry) or 1.8 (with monopropellant) | * Mass reduced to 1.76 (dry) or 1.8 (with monopropellant) | ||
− | ; | + | ;[[0.24]] |
* Cost increased from 2000 to 3200 (12 of which is monoprop cost) | * Cost increased from 2000 to 3200 (12 of which is monoprop cost) | ||
− | ; | + | ;[[0.23]] |
* Added 10 units of monopropellant storage, increasing total mass from 4.5 to 4.54 | * Added 10 units of monopropellant storage, increasing total mass from 4.5 to 4.54 | ||
− | ; | + | ;[[0.20]] |
* Initial Release | * Initial Release | ||
{{Parts}} | {{Parts}} | ||
[[Category:Command modules]] | [[Category:Command modules]] |
Revision as of 13:26, 3 May 2015
PPD-12 Cupola Module | |||||
Command pod by Jebediah Kerman's Junkyard and Spacecraft Parts Co | |||||
Radial size | Small, Large | ||||
Cost | (total) | 1 600.00 | |||
(dry) | 1 588.00 | ||||
Mass | (total) | 0.98 t | |||
(dry) | 0.94 t | ||||
Drag | 0.2 | ||||
Max. Temp. | 2000 K | ||||
Volume | ? | ||||
Impact Tolerance | 8 m/s | ||||
Research | Command Modules | ||||
Unlock cost | 10 200 | ||||
Since version | 0.20 | ||||
Part configuration | cupola.cfg | ||||
Command module | |||||
Pitch torque | 9.0 kN·m | ||||
Yaw torque | 9.0 kN·m | ||||
Roll torque | 9.0 kN·m | ||||
Electricity required for torque |
| ||||
Crew capacity | (maximum) | 1 | |||
(required) | 1 | ||||
Monopropellant | 10 | ||||
Electric capacity | 200.0 ⚡ | ||||
SAS level | × None |
The PPD-12 Cupola Module is a Command Module housing one Kerbal crew member during its mission. It is inspired by the Cupola module of the International Space Station.
Contents
Usage
The Cupola Module's main purpose is to provide a good outside view from space stations or bases. It is heavier and larger than the other command pods and cockpits which have a crew capacity of one, while still being lighter than parts with higher crew capacities. It is also quite fragile, has higher drag than most other parts, and has a relatively high energy capacity.Product description
The PPD-12 is one of the few parts in Kerbal Space Program that is covered in multi-layer insulation.
“ | The PPD-12 was developed to provide a high visibility control room for orbital stations, and a place for thoughtful Kerbals to contemplate the beauty of the cosmos. | ” |
Trivia
- There is a photo of two Kerbonauts on the right side of the cockpit.
- A few sticky notes can be found as well:
“ | Left the emergency slide rule in the bottom right cabinet. B.K. P.S. I ate all the snacks — On the roll indicator |
” |
“ | Stop using bits of metal as fuses YOU HAVE SPARES! — On the fuse box |
” |
Changes
- Mass reduced to 1.76 (dry) or 1.8 (with monopropellant)
- Cost increased from 2000 to 3200 (12 of which is monoprop cost)
- Added 10 units of monopropellant storage, increasing total mass from 4.5 to 4.54
- Initial Release