Difference between revisions of "PPD-12 Cupola Module"
From Kerbal Space Program Wiki
m (* minor stuff.) |
(→Trivia) |
||
(16 intermediate revisions by 14 users not shown) | |||
Line 1: | Line 1: | ||
{{:PPD-12 Cupola Module/Box}} | {{:PPD-12 Cupola Module/Box}} | ||
+ | |||
The '''PPD-12 Cupola Module''' is a [[Command Module]] housing one [[Kerbal]] crew member during its mission. It is inspired by the [[w:Cupola (ISS module)|Cupola module]] of the International Space Station. | The '''PPD-12 Cupola Module''' is a [[Command Module]] housing one [[Kerbal]] crew member during its mission. It is inspired by the [[w:Cupola (ISS module)|Cupola module]] of the International Space Station. | ||
== Usage == | == Usage == | ||
− | [[File:Cupola panorama.jpg|thumb|left|Inside panorama view on [[Kerbin]]]] The Cupola Module's main purpose is to provide a good outside view from space stations or bases. It is | + | [[File:Cupola panorama.jpg|thumb|left|Inside panorama view on [[Kerbin]]]] |
+ | |||
+ | The Cupola Module's main purpose is to provide a good outside view from space stations or bases. It is heavier and larger than the other command pods and cockpits which have a crew capacity of one, while still being lighter than parts with higher crew capacities. It is also quite fragile, has higher [[drag]] than most other parts, and has a relatively high energy capacity. | ||
− | + | == Product description == | |
− | == | + | {{Quote|The PPD-12 was developed to provide a high visibility control room for orbital stations, and a place for thoughtful Kerbals to contemplate the beauty of the cosmos.|manufacturer=JKJSP}} |
− | {{Quote | ||
− | |The PPD-12 was developed to provide a high visibility control room for orbital stations, and a place for thoughtful Kerbals to contemplate the beauty of the cosmos. | ||
− | | | ||
== Trivia == | == Trivia == | ||
+ | * The PPD-12 is one of the few parts in Kerbal Space Program that is covered in [[w:Multi-layer insulation|multi-layer insulation]]. (must be tested in-game) | ||
* There is a photo of two [[Kerbal|Kerbonauts]] on the right side of the cockpit. | * There is a photo of two [[Kerbal|Kerbonauts]] on the right side of the cockpit. | ||
* A few sticky notes can be found as well: | * A few sticky notes can be found as well: | ||
− | {{Quote | + | {{Quote|Left the emergency slide rule in the bottom right cabinet.<br>B.K.<br>P.S. I ate all the snacks|On the roll indicator}} |
− | |Left the emergency slide rule in the bottom right cabinet.<br>B.K.<br>P.S. I ate all the snacks | + | {{Quote|Stop using bits of metal as fuses<br>YOU HAVE <u>SPARES!</u>|On the fuse box}} |
− | |On the roll indicator}} | ||
− | + | * The initials B.K. on the first sticky note is most likely referring to Bill or Bob Kerman | |
− | |||
− | |||
== Changes == | == Changes == | ||
− | ; | + | ;[[1.2]] |
+ | * IVA improved | ||
+ | ;[[0.25]] | ||
+ | * Mass reduced to 1.76 (dry) or 1.8 (with monopropellant) | ||
+ | ;[[0.24]] | ||
+ | * Cost increased from 2000 to 3200 (12 of which is monoprop cost) | ||
+ | ;[[0.23]] | ||
+ | * Added 10 units of monopropellant storage, increasing total mass from 4.5 to 4.54 | ||
+ | ;[[0.20]] | ||
* Initial Release | * Initial Release | ||
{{Parts}} | {{Parts}} | ||
+ | [[Category:Command modules]] |
Latest revision as of 10:16, 11 July 2020
PPD-12 Cupola Module | |||||
Command pod by Jebediah Kerman's Junkyard and Spacecraft Parts Co | |||||
Radial size | Small, Large | ||||
Cost | (total) | 1 600.00 ![]() | |||
(dry) | 1 588.00 ![]() | ||||
Mass | (total) | 0.98 t | |||
(dry) | 0.94 t | ||||
Drag | 0.2 | ||||
Max. Temp. | 2000 K | ||||
Volume | ? | ||||
Impact Tolerance | 8 m/s | ||||
Research | ![]() | ||||
Unlock cost | 10 200 ![]() | ||||
Since version | 0.20 | ||||
Part configuration | cupola.cfg | ||||
Command module | |||||
Pitch torque | 9.0 kN·m | ||||
Yaw torque | 9.0 kN·m | ||||
Roll torque | 9.0 kN·m | ||||
Electricity required for torque |
| ||||
Crew capacity | (maximum) | 1 ![]() | |||
(required) | 1 ![]() | ||||
Monopropellant | 10 ![]() | ||||
Electric capacity | 200.0 ⚡ | ||||
SAS level | × None |
The PPD-12 Cupola Module is a Command Module housing one Kerbal crew member during its mission. It is inspired by the Cupola module of the International Space Station.
Contents
Usage
![](/images/thumb/d/d6/Cupola_panorama.jpg/300px-Cupola_panorama.jpg)
Inside panorama view on Kerbin
The Cupola Module's main purpose is to provide a good outside view from space stations or bases. It is heavier and larger than the other command pods and cockpits which have a crew capacity of one, while still being lighter than parts with higher crew capacities. It is also quite fragile, has higher drag than most other parts, and has a relatively high energy capacity.
Product description
“ | The PPD-12 was developed to provide a high visibility control room for orbital stations, and a place for thoughtful Kerbals to contemplate the beauty of the cosmos. — Jebediah Kerman's Junkyard and Spacecraft Parts Co |
” |
Trivia
- The PPD-12 is one of the few parts in Kerbal Space Program that is covered in multi-layer insulation. (must be tested in-game)
- There is a photo of two Kerbonauts on the right side of the cockpit.
- A few sticky notes can be found as well:
“ | Left the emergency slide rule in the bottom right cabinet. B.K. P.S. I ate all the snacks — On the roll indicator |
” |
“ | Stop using bits of metal as fuses YOU HAVE SPARES! — On the fuse box |
” |
- The initials B.K. on the first sticky note is most likely referring to Bill or Bob Kerman
Changes
- IVA improved
- Mass reduced to 1.76 (dry) or 1.8 (with monopropellant)
- Cost increased from 2000 to 3200 (12 of which is monoprop cost)
- Added 10 units of monopropellant storage, increasing total mass from 4.5 to 4.54
- Initial Release