Difference between revisions of "Engine Pre-cooler"
m |
m (Fix link to box) |
||
| (10 intermediate revisions by 8 users not shown) | |||
| Line 1: | Line 1: | ||
| − | {{: | + | {{:Engine Pre-cooler/Box}} |
| − | The ''' | + | The '''Engine Pre-cooler''' is a combination of an [[air intake]] and a small [[liquid fuel tank]]. It is the most efficient inline supersonic intake offering markedly better performance than the [[Mk1 Diverterless Supersonic Intake]] at mach speeds higher than ~3. |
| + | |||
| + | The precooler is ''in principle'' a slightly better heat conductor than other (non-radiator) parts with double the heatConductivity and it also has superior heat emission which allows it to act as a passive radiator and wick away heat more effectively, this effect is not limited to engines nor to atmospheric use. However ''in practice'' it is very difficult to observe any actual benefit from these thermal characteristics and as it is also more effective at absorbing heat from the environment it may actually make overheating worse when the heat source is external (i.e. from re-entry) rather than internal. | ||
Prior to [[0.24]] it was purely cosmetic but could be easily mistaken for an air intake. This part was originally developed for the C7 Spaceplane pack, and has become a stock part since 0.15.0 and the introduction of the [[Spaceplane Hangar]]. | Prior to [[0.24]] it was purely cosmetic but could be easily mistaken for an air intake. This part was originally developed for the C7 Spaceplane pack, and has become a stock part since 0.15.0 and the introduction of the [[Spaceplane Hangar]]. | ||
== Product description == | == Product description == | ||
| − | {{Quote| | + | {{Quote|Advanced materials allow this cooler to wick away the heat from attached engines. In addition, it features additional intake area optimized for supersonic flight and powerful static suction.|C7 Aerospace Division |
| + | }} | ||
== Changes == | == Changes == | ||
| + | |||
| + | ; [[1.0.5]] | ||
| + | * Changed description | ||
| + | * Increased dry mass from 0.15t to 0.175t | ||
| + | * Impact tolerance halved from 20 to 10m/s | ||
; [[0.24]] | ; [[0.24]] | ||
* Added fuel tank with 40 units of liquid fuel | * Added fuel tank with 40 units of liquid fuel | ||
| Line 15: | Line 23: | ||
* Initial stock release | * Initial stock release | ||
| + | [[File:Radial engine body.png|left|thumb|the previous model: Radial engine body]] | ||
{{Parts}} | {{Parts}} | ||
[[Category:Air intakes]] | [[Category:Air intakes]] | ||
| − | |||
Latest revision as of 09:27, 13 October 2024
| Engine Pre-cooler | ||
 | ||
| Air intake by C7 Aerospace Division | ||
| Radial size | Small, Radial mounted | |
| Cost | (total) | 1 650.00 
|
| (dry) | 1 618.00
| |
| Mass | (total) | 0.375 t |
| (dry) | 0.175 t | |
| Drag | 0.3-0.2 | |
| Max. Temp. | 2000 K | |
| Impact Tolerance | 10 m/s | |
| Research |  Hypersonic Flight
| |
| Unlock cost | 6 200
| |
| Since version | 0.15 | |
| Part configuration | engineBodyRadial.cfg | |
| Intake speed | 30 m/s | |
| Intake area | 0.5 m2 | |
| Liquid fuel | 40 
| |
| Intake air | 5 
| |
The Engine Pre-cooler is a combination of an air intake and a small liquid fuel tank. It is the most efficient inline supersonic intake offering markedly better performance than the Mk1 Diverterless Supersonic Intake at mach speeds higher than ~3.
The precooler is in principle a slightly better heat conductor than other (non-radiator) parts with double the heatConductivity and it also has superior heat emission which allows it to act as a passive radiator and wick away heat more effectively, this effect is not limited to engines nor to atmospheric use. However in practice it is very difficult to observe any actual benefit from these thermal characteristics and as it is also more effective at absorbing heat from the environment it may actually make overheating worse when the heat source is external (i.e. from re-entry) rather than internal.
Prior to 0.24 it was purely cosmetic but could be easily mistaken for an air intake. This part was originally developed for the C7 Spaceplane pack, and has become a stock part since 0.15.0 and the introduction of the Spaceplane Hangar.
Product description
| “ | Advanced materials allow this cooler to wick away the heat from attached engines. In addition, it features additional intake area optimized for supersonic flight and powerful static suction. — C7 Aerospace Division |
” |
Changes
- Changed description
- Increased dry mass from 0.15t to 0.175t
- Impact tolerance halved from 20 to 10m/s
- Added fuel tank with 40 units of liquid fuel
- Added air intake
- Adjusted dry mass (from 0.3 to 0.15) and costs (from 550 to 1650)
- Initial stock release
