Difference between revisions of "LT-2 Landing Strut"
(Offset tool usage) |
|||
| Line 8: | Line 8: | ||
The LT-2 Landing Strut is used as a support when landing vertically, or at least attempting to. It is connected radially and extends with the {{Key press|G}} key (default). It extends much farther than its smaller cousin the [[LT-1 Landing Strut|LT-1]] through a unique telescoping action, making it suitable for landers with larger engines. | The LT-2 Landing Strut is used as a support when landing vertically, or at least attempting to. It is connected radially and extends with the {{Key press|G}} key (default). It extends much farther than its smaller cousin the [[LT-1 Landing Strut|LT-1]] through a unique telescoping action, making it suitable for landers with larger engines. | ||
| − | Although comparatively long, LT-2 landing struts still need to be placed low on a rocket. They extend far enough to be used with the [[Rockomax "Poodle" Liquid Engine|Poodle]], [[LV-T30 Liquid Fuel Engine|LV-T30]], and [[LV-T45 Liquid Fuel Engine]]s, but cannot reach past the [[LV-N Atomic Rocket Motor|LV-N]] or [[Rockomax "Mainsail" Liquid Engine|Mainsail]]. A workaround to this is using [[Parts#Adapters.2C_Couplers_.26_Struts|girders, I-beams, or panels]] to | + | Although comparatively long, LT-2 landing struts still need to be placed low on a rocket. They extend far enough to be used with the [[Rockomax "Poodle" Liquid Engine|Poodle]], [[LV-T30 Liquid Fuel Engine|LV-T30]], and [[LV-T45 Liquid Fuel Engine]]s, but cannot reach past the [[LV-N Atomic Rocket Motor|LV-N]] or [[Rockomax "Mainsail" Liquid Engine|Mainsail]]. A workaround to this is using [[Parts#Adapters.2C_Couplers_.26_Struts|girders, I-beams, or panels]] or just simply using the offset tool to place the landing leg lower on the rocket. You can check if it will clear the engine by moving your lander in the VAB so that it's landing legs just touch the ground. Do be aware, though, that all landing legs have suspension and will get slightly shorter under heavier rockets. |
LT-2 Landing struts can be set to be either extended or retracted at launch. This is done by right-clicking the part in the [[VAB]] or [[SPH]] and clicking the relevant button. The landing struts can be toggled in flight with the {{Key press|G}} key or hitting the “extend gear” button on the HUD. While in motion the legs can produce substantial forces, potentially resulting in a several meter “hop”. If the leg collides with another part of the rocket, it can break connections and push that part away.<!--- [[http://kerbalspaceprogram.com/forum/index.php?topic=11407.0]]--> | LT-2 Landing struts can be set to be either extended or retracted at launch. This is done by right-clicking the part in the [[VAB]] or [[SPH]] and clicking the relevant button. The landing struts can be toggled in flight with the {{Key press|G}} key or hitting the “extend gear” button on the HUD. While in motion the legs can produce substantial forces, potentially resulting in a several meter “hop”. If the leg collides with another part of the rocket, it can break connections and push that part away.<!--- [[http://kerbalspaceprogram.com/forum/index.php?topic=11407.0]]--> | ||
Revision as of 22:03, 1 February 2016
| LT-2 Landing Strut | ||
 | ||
| Landing leg by Moving Parts Experts Group | ||
| Radial size | Radial mounted | |
| Cost | (total) | 340.00 
|
| Mass | (total) | 0.100 t |
| Drag | 0.2 | |
| Max. Temp. | 2000 K | |
| Impact Tolerance | 12 m/s | |
| Research |  Advanced Landing
| |
| Unlock cost | 4 100
| |
| Since version | 0.14 | |
| Part configuration | landingLegLT-2.cfg | |
| Retractable | Yes | |
| Brake torque | No | |
| Steering range | No | |
| Packed volume | 300 l | |
The LT-2 Landing Strut is primarily used to land safely on celestial bodies. Prior to its introduction in 0.14, winglets were often the preferred method of providing landing legs for Mün missions.
Usage
The LT-2 Landing Strut is used as a support when landing vertically, or at least attempting to. It is connected radially and extends with the G key (default). It extends much farther than its smaller cousin the LT-1 through a unique telescoping action, making it suitable for landers with larger engines.
Although comparatively long, LT-2 landing struts still need to be placed low on a rocket. They extend far enough to be used with the Poodle, LV-T30, and LV-T45 Liquid Fuel Engines, but cannot reach past the LV-N or Mainsail. A workaround to this is using girders, I-beams, or panels or just simply using the offset tool to place the landing leg lower on the rocket. You can check if it will clear the engine by moving your lander in the VAB so that it's landing legs just touch the ground. Do be aware, though, that all landing legs have suspension and will get slightly shorter under heavier rockets.
LT-2 Landing struts can be set to be either extended or retracted at launch. This is done by right-clicking the part in the VAB or SPH and clicking the relevant button. The landing struts can be toggled in flight with the G key or hitting the “extend gear” button on the HUD. While in motion the legs can produce substantial forces, potentially resulting in a several meter “hop”. If the leg collides with another part of the rocket, it can break connections and push that part away.
The maximum safe landing speed for an LT-2 landing strut is ~12 m/s. Landings with massive rockets or on rough terrain may need to be slower to avoid ripping off landing legs.
As of 0.23.5, landing leg mass is counted. This is in contrast to landing gear.
In the current version, 1.0.5, it is possible to lock the suspension.
Product description
| “ | The LT-2 Landing Strut offers a heavy-duty method for planting yourself firmly on the ground, without the severe consequences that usually accompany planting yourself firmly on the ground. | ” |
Changes
- Suspension
- Initial release
