Difference between revisions of "Mk1 Command Pod"
GregroxMun (talk | contribs) (→Changes) |
GregroxMun (talk | contribs) (Fixed Mercury Spacecraft Image) |
||
| Line 1: | Line 1: | ||
{{:Command Pod Mk1/Box}} | {{:Command Pod Mk1/Box}} | ||
| − | The '''Command Pod Mk1''' is a [[command module]] capable of housing a single [[Kerbal]] during a mission. It closely resembles a [http:// | + | The '''Command Pod Mk1''' is a [[command module]] capable of housing a single [[Kerbal]] during a mission. It closely resembles a [http://www.museumofflight.org/files/imagecache/lightbox/TMOF_MercuryCapsule1_P1.jpg Mercury capsule.] |
== Usage == | == Usage == | ||
Revision as of 13:51, 8 July 2014
| Mk1 Command Pod | |||||
 | |||||
| Command pod by Kerlington Model Rockets and Paper Products Inc | |||||
| Radial size | Small, Tiny | ||||
| Cost | (total) | 635.00 
| |||
| (dry) | 588.00
| ||||
| Mass | (total) | 0.840 t | |||
| (dry) | 0.706 t | ||||
| Drag | 0.15-0.2 | ||||
| Max. Temp. | 2200 K | ||||
| Impact Tolerance | 14 m/s | ||||
| Research |  Start
| ||||
| Unlock cost | 0
| ||||
| Since version | 0.7.3 | ||||
| Part configuration | mk1Pod_v2.cfg | ||||
| Crew capacity | (maximum) | 1 
| |||
| (required) | 1
| ||||
| SAS level | × None | ||||
| Torque | 5 kN·m | ||||
| Electricity required |
| ||||
| Experiment | Crew Report | ||||
| Collectable | No | ||||
| Rerunnable | Yes | ||||
| Resettable | Yes | ||||
| Electricity required | None | ||||
| Antenna type | Internal | ||||
| Antenna rating | 5 km | ||||
| Lift generated | 0.35 | ||||
| Packed volume | None | ||||
| Inventory Slots | 1 slots | ||||
| Volume limit | 50 l | ||||
| Monopropellant | 10 
| ||||
| Electric capacity | 50 ⚡ | ||||
The Command Pod Mk1 is a command module capable of housing a single Kerbal during a mission. It closely resembles a Mercury capsule.
Usage
Usually placed at the top of the rocket, the Command Pod Mk1 provides all functionality of a command module. It has half the torque power of most other manned command modules. This is often sufficient for smaller rockets, though larger ones will require additional control systems.
The Mk1 Command Pod features a tiny radial size node on top, typically used for attaching a Mk16 Parachute, and a small radial size node on the bottom. The pod's crew hatch is outfitted with a small window through which an occupying Kerbal can look out during IVA. On the outside there are two rungs of ladders below the hatch.
The Mk1 Command Pod is also the first command module available in the career mode.
Description
| “ | Originally built as a placeholder for a demonstration mock-up of a rocket, the Mk1 Command Pod was heralded as a far safer and more reliable option than its predecessors by rocket scientists throughout the world. It is now commonly seen in active service. — Kerlington Model Rockets and Paper Products Inc. |
” |
Trivia
The model for this parts was replaced in version 0.16, there is a memorial to the original located at the Kerbal Space Center.[1] An old command pod can also be found at the Insular Airfield on an island near KSC, in one of the hangars.
Gallery
The original model from versions before 0.16. Back then it could also hold three kerbals.
The memorial for the pre 0.16 model outside of KSC.
Changes
- Added Monopropellant
- Added ElectricCharge
- Part rebalancing: Mass reduced from 1.0 to 0.8, and crew capacity reduced from 3 to 1.
- New part model.
- Exposed Kd, Ki and Kp parameters for tuning the SAS and CommandPod modules
- (Bug fix) Pod cannot be dropped if an Escape Tower (PunchOut addon) is attached
- Initial Release
References
| ||||||||||||||||||||||||||||
